Welcome to Installation

cancel
Showing results for 
Search instead for 
Did you mean: 
Need help?

Installation of Explora 2 in a complex

SOLVED
12 REPLIES 12
Trending

Re: Installation of Explora 2 in a complex

So either a faulty satellite feed or it is in fact a terrestrial antenna port. Have a look at the socket panel and look for labelling, or post a screen shot for us to have a look at.

Octo LNB; 2 by 2x4 MS; 2 by ES 5-2; Dedicated PSU for LNB, ES's, MS's; HD PVR 4P x 2; Explora 1; DSD 660; FSM
New poster

Re: Installation of Explora 2 in a complex

Thanks a lot guys. The problem is one of the ports on the wall. My old decoder doesn't pick signal from this port. All cables are working fine. 

New poster

Re: Installation of Explora 2 in a complex

Yep, it is on port A; I will try B. 

I will try all these suggestions tonight and see. 

Red Carpet

Re: Installation of Explora 2 in a complex

Since I'm here, one more basic possibility we may have missed;

I presume the Explora is connected to port A on the 5-2 switch? It musn't be connected to the numbered ports.

 

If it is on A, now try B.

 

Then do a factory defaults reset again, followed by a manual install with Indexes 0, 1 & 2 selected.

The respective frequencies should be 1210, 1420 & 1680.

Do all the indexes first, then all the frequencies.

 

Pre-made cables are unlikely to be the problem, but it's possible.

New poster

Re: Installation of Explora 2 in a complex

Thanks GeoffD. The BC has just confirmed there are no special settings I need, it should connect. The only thing I can think of now is the new LNB cables which I bought to connect to the switch. When I get home I will try connecting my old decorder using the new cables and see if that is the problem. another question though, do LNB cables come with different strength of signal transmissions? 

 

Just to confirm, Yes two cables connected from the wall to the switch and one from the switch to the decoder. 

Trending

Re: Installation of Explora 2 in a complex

There is the first part of your answer!

The Explora switch 5-2 MUST be provided with TWO connections minimum to the LNB, connected to ports H/L and V/L to even start working properly.

Even this is only a temporary measure as soon 4 connections will be required.

Only then can you hope to get the Explora to start up correctly. BOTH LNB connections MUST  be satellite feeds.

 

Both must be universal LNB feeds, operating independently from each other.

Only the BC can confirm what they are.

If not as above, forget about getting an Explora to work.

Octo LNB; 2 by 2x4 MS; 2 by ES 5-2; Dedicated PSU for LNB, ES's, MS's; HD PVR 4P x 2; Explora 1; DSD 660; FSM
Highlighted
New poster

Re: Installation of Explora 2 in a complex

Hi, sorry if you miss undertood my reply... The older decoder is not connected through the switch, directly from the wall and it is not an Explora. So far I've been connecting one decoder at a time - Explora decoder through the switch (signal low or poor quality). The older decoder is from the year 2012. 

Trending

Re: Installation of Explora 2 in a complex

So which model is the other decoder? How is it connected to the 5-2 switch?

If both are connected to Unicable ports then the problem IS related to a UB  clash between the decoders.

It would really help if you answered my questions I asked.

 

 

Octo LNB; 2 by 2x4 MS; 2 by ES 5-2; Dedicated PSU for LNB, ES's, MS's; HD PVR 4P x 2; Explora 1; DSD 660; FSM
New poster

Re: Installation of Explora 2 in a complex

Thanks, I will check and contact BC to assist. 

New poster

Re: Installation of Explora 2 in a complex

Hi. I have a decorder (not explora) which is currently working well with good signal. From the wall I have two LNB's to the switch and then from the switch to the decorder. I didn't check UB's after resetting to factory default. Would the status light on the switch be on though if the signal was poor?