@Optimist wrote:Correction - my original Explora 1 adaptor is the same model as yours, my spare one isn't... the guy who gave that Explora 1 to me must have mixed them up.
I thought the lower spec adaptor (3.33A) might give hassles with the higher spec Exp1 (3.75) ? As I understand it, lower can run on higher and will use only what's needed, but not the other way round ? Keep in mind , I'm clueless when it comes to electricity I do light bulbs and that's it
Sorry Geoff if I digress in your topic
SLNB LMX501| Explora 2A (Primary 4,5,6) Explora 2A (Secondary 0,1,2) | Xtraview - decoders same room | 3 distributed HDMI endpoints via 2x4 Matrix
and Cat6 | 200/100 Fibre (OpenServe/Afrihost Premium UnCapped) | HD 5S in holiday mode
Definitely.
Exp1
Epx 2A
SLNB LMX501| Explora 2A (Primary 4,5,6) Explora 2A (Secondary 0,1,2) | Xtraview - decoders same room | 3 distributed HDMI endpoints via 2x4 Matrix
and Cat6 | 200/100 Fibre (OpenServe/Afrihost Premium UnCapped) | HD 5S in holiday mode
Correction - my original Explora 1 adaptor is the same model as yours, my spare one isn't... the guy who gave that Explora 1 to me must have mixed them up.
Thought it was odd that the output amperage specs didn't match...
Luke, only just saw your posts. Are you sure that was for your Explora 1, my adapter model for it is certain.
@Optimist wrote:Turns out there were specs on the adaptor, not seen as it's lightly placed in black ink on a black surface instead of printed
Attempted photos are useless.
MODEL: AD10250LF
INPUT: 100 to 240V AC, 50/60Hz, 1.0A
OUTPUT: 12V DC, 3.33A, shows centre pin is the usual positive
The outer diameter of the plug measured with a hovering ruler and magnifying glass is what looks like exactly 5mm.
This is the 2A ^^
SLNB LMX501| Explora 2A (Primary 4,5,6) Explora 2A (Secondary 0,1,2) | Xtraview - decoders same room | 3 distributed HDMI endpoints via 2x4 Matrix
and Cat6 | 200/100 Fibre (OpenServe/Afrihost Premium UnCapped) | HD 5S in holiday mode
Turns out there were specs on the adaptor, not seen as it's lightly placed in black ink on a black surface instead of printed
Attempted photos are useless.
EDIT: This info is now believed to be for the Explora 2A - see later posts.
MODEL: AD10250LF
INPUT: 100 to 240V AC, 50/60Hz, 1.0A
OUTPUT: 12V DC, 3.33A, shows centre pin is the usual positive
The outer diameter of the plug measured with a hovering ruler and magnifying glass is what looks like exactly 5mm.
Explora 1
2A , same , but 3.33A
SLNB LMX501| Explora 2A (Primary 4,5,6) Explora 2A (Secondary 0,1,2) | Xtraview - decoders same room | 3 distributed HDMI endpoints via 2x4 Matrix
and Cat6 | 200/100 Fibre (OpenServe/Afrihost Premium UnCapped) | HD 5S in holiday mode
Explora 1;
You're going to struggle with this Geoff - there's no info printed on the power adaptor's surfaces (I have two), nor anything I can find in the "manual" booklet.
All there is is the same info on the back of the decoder by its socket, and on its label;
+12V "DC" (the DC symbol)
3.75A Max.
Plug - don't have a caliper, seems to be the standard mid-sized barrel type fitting for low powered DC supply.
Bear in mind that there was a slight difference in size with the HD PVR 2U's plug & socket compared to the standard generally found.
(I'm not likely to be around most of today.)
Hi all,
I am working on a project to develop a reliable backup power supply for all small devices that run on DC power.
Could those of you with decoders that have external PSUs please help with the specs for the external power bricks for the Explora 1, Explora 2A, Explora 3A, HD 4- & 5- series HD decoders, please? The idea is to come up with a simple and cheap power supply for small devices
The format of the info is normally something like this:
Input:
100-240 V; 50/60 Hz; 2A; pf 0.8
Output:
19V DC; 5A
DC plug type if known or a measurement of the outer diameter of the DC power plug connector.
Details required are:
Input:
AC Voltage, Frequency, Current, powerfactor if available.
Output:
DC Volts, Current and watts if available
Any other loose power supplies you might be using for ADSL modems and routers optic fibre ONTs; WiFi AP's and routers will also be very useful.
The idea is to see if it feasible to design a universal backup power source that consists of a Battery Charger, a battery for 10 to 24 hours of backup and a simple multi-plug DC output suitable for a range of devices.
I have already done something like this for my daughter for her CCTV DVR and camera setup that has been very successful.
Octo LNB; 2 by 2x4 MS; 2 by ES 5-2; Dedicated PSU for LNB, ES's, MS's; HD PVR 4P x 2; Explora 1; DSD 660; FSM
© MultiChoice Support Services (Pty) Ltd